Ubiquiti UniFi E7 Campus — Indoor/Outdoor Enterprise WiFi 7 Access Point with 10 Spatial Streams, PRISM Active RF Filtering, Directional Antennas, 10 GbE Uplink and IP67 (Door Kit) Weatherproofing

E7-Campus

Ubiquiti UniFi E7 Campus — Indoor/Outdoor Enterprise WiFi 7 Access Point with 10 Spatial Streams, PRISM™ Active RF Filtering, Directional Antennas, 10 GbE Uplink and IP67 (Door Kit) Weatherproofing

Features

• Indoor/outdoor enterprise WiFi 7 access point designed to blanket large campus environments — university grounds, business parks, school yards, hospital precincts, retail centres and outdoor venues — with a single high-throughput AP.
• 10 spatial streams: 4×4 MU-MIMO on 6 GHz, 4×4 on 5 GHz and 2×2 on 2.4 GHz for full backwards compatibility, with 8 BSSIDs per radio.
• PRISM™ active RF filtering — Ubiquiti's noise-rejection technology suppresses external interference so the AP keeps performing in congested RF environments typical of dense campus deployments.
• Integrated directional antennas: 12 dBi at 90° × 50° on 6 GHz, 12 dBi at 100° × 55° on 5 GHz and 9 dBi at 90° × 80° on 2.4 GHz — engineered for the wide-arc coverage that campus walkways and quadrangles need.
• Peak WiFi throughput: 11.5 Gbps on 6 GHz (320 MHz channel), 8.6 Gbps on 5 GHz (240 MHz) and 688 Mbps on 2.4 GHz.
• Designed for 1,000+ concurrent clients and approximately 465 m² (5,000 ft²) of coverage per AP.
• 10 GbE primary RJ45 uplink with a redundant 1 GbE secondary port — survive a switch port or cable failure without dropping coverage.
• PoE++ (802.3bt) powered at up to 44W consumption (42.5–57V DC) — single-cable installation.
• IPX6 weatherproof out of the box, upgradeable to IP67 with the included Waterproof Door Kit.
• Articulating wall and pole mount included (pole diameter 25–63.5 mm); VESA mount optional.
• Wind loading rated to 164.75 N at 200 km/h; -30 to 60 °C ambient operation; 5–95% non-condensing humidity.
• Stainless-steel and aluminium-alloy mount hardware; UV-stabilised polycarbonate and aluminium-alloy enclosure.
• Centrally managed through UniFi Network 9.0.114 or later — zero per-AP licensing.
• Certifications: FCC, IC.

Specifications

Professional Overview

The UniFi E7 Campus is Ubiquiti's indoor/outdoor enterprise WiFi 7 access point engineered for wide-arc campus environments — university grounds and lecture quads, business parks, school playgrounds, hospital precincts, council halls, large retail centres and outdoor hospitality venues. Where the E7 Audience sectorises a stadium tribune with narrow-beam antennas, the E7 Campus spreads coverage across a much wider aperture — 12 dBi internal directional patterns at 90° × 50° (6 GHz), 100° × 55° (5 GHz) and 9 dBi at 90° × 80° (2.4 GHz) — designed to blanket walkways, plazas and large rooms rather than focus into a wedge.

The radio architecture is tri-band 10-stream: 4×4 MU-MIMO on 6 GHz, 4×4 on 5 GHz and 2×2 on 2.4 GHz, with up to 8 BSSIDs per radio. Peak rates reach 11.5 Gbps on 6 GHz (320 MHz channel), 8.6 Gbps on 5 GHz (240 MHz) and 688 Mbps on 2.4 GHz, and the AP supports 1,000+ concurrent clients over approximately 465 m² (5,000 ft²) of coverage. Crucially, the Campus also carries Ubiquiti's PRISM™ active RF filtering technology — designed to actively reject external noise and adjacent-AP interference, which is the failure mode that limits ordinary outdoor APs in dense municipal environments.

On the wired side, a primary 10 GbE RJ45 uplink is backed by a redundant 1 GbE secondary port, so a single switch port or cable failure does not blackout outdoor coverage during a teaching day or event. The AP is powered by PoE++ (802.3bt, 42.5–57V DC, up to 44W consumption) from any UniFi PoE++ switch. Mounting is by an included articulating wall/pole mount (25–63.5 mm pole diameters) with a VESA option, and the enclosure is rated for outdoor exposure: IPX6 standard, upgradable to IP67 by fitting the included Waterproof Door Kit, with a wind loading specification of 164.75 N at 200 km/h.

Build quality is uprated for permanent outdoor service: a UV-stabilised polycarbonate radome over an aluminium-alloy chassis with stainless-steel and aluminium-alloy mount hardware, rated for -30 to 60 °C ambient operation and 5–95% non-condensing humidity. Certifications cover FCC and IC. Management is entirely through UniFi Network 9.0.114 or later — no per-AP licence, full RF planning, fast roaming, RADIUS and rogue AP detection. Australian stock from ARC IP Networks.

Ubiquiti E7-Campus: WiFi 7 access point

The Access Point E7 Campus is a UniFi WiFi 7 access point with 10 spatial streams, a rated coverage area of 465 m² (5,000 ft²) and 1,000 concurrent clients.

On the wired side the uplink is 10 GbE, it is powered by PoE++, and draws at most 44W.

It carries a IPX6 IP67 with Waterproof Door Kit (Included) rating, so unlike an ordinary indoor AP it can be mounted outside under normal Australian conditions. Read the rating literally: it covers water, not immersion, and it is not a reason to site the unit where it will sit in standing water.

In Australia the ACMA class licence opens 5925–6425 MHz to WiFi — the lower 500 MHz of the 6 GHz band, not the full 5925–7125 MHz range the United States allows. There are still more clean channels there than anywhere in 5 GHz, but plan channel width accordingly: a 320 MHz channel consumes most of what is available here.

Radios and throughput

Supported data rates

These are modulation-coding-scheme ceilings measured at the radio, not speeds a client will see. Real throughput depends on the client's own radio, the channel width you can actually use, distance and how much of the band your neighbours are already occupying. Our UniFi access point comparison puts the range side by side.

Uplink and power

Power comes down the Ethernet run as PoE++, drawing up to 44W. On a switch that shares one PoE budget across every port, add up the draw of every AP before you commit — the UniFi switch range lists the total availability for each model.

The 10 GbE uplink is there for a reason: a WiFi 7 radio can move more than a gigabit, and on a 1 GbE port the switch becomes the bottleneck before the radio does. It will negotiate down to 1 GbE and work, but you lose the headroom you paid for.

Who the E7-Campus suits

• Campuses and large sites needing enterprise WiFi 7 indoors and out
• Deployments standardising on the UniFi Enterprise range
• High-density areas where client count is the design driver
• Projects going through the Ubiquiti Enterprise Program — contact us for project pricing

Physical and mounting

The mounting hardware listed above is supplied in the box.

Rated for -30 to 60° C (-22 to 140° F). Worth checking against a roof space in an Australian summer, which routinely runs hotter than an occupied room.

Management and requirements

Like every UniFi access point, the E7-Campus is adopted and managed by a UniFi controller — a Cloud Gateway or Dream Machine, a Cloud Key, or UniFi hosting. The AP does not run the controller itself, and it is not a standalone router: it provides the WiFi, while routing, firewall and VLANs live on the gateway.

It requires UniFi Network 9.0.114 and later. An older controller will not adopt it until you update.

Buy the Ubiquiti E7-Campus in Australia

ARC IP Networks is an authorised Ubiquiti reseller supplying the E7-Campus from Australian stock, with full manufacturer warranty and fast shipping nationwide.

• Authorised Ubiquiti reseller — genuine Australian stock, not grey import
• Full manufacturer warranty with local RMA support
• Competitive Australian pricing, monitored against the local market daily
• Fast dispatch Australia-wide, or collect from our warehouse
• Trade and project pricing for installers, MSPs and multi-site rollouts

Browse the full UniFi access point range, plus cloud gateways, switches and the Protect camera range. New to UniFi? Start with the complete UniFi buying guide, or compare the APs directly in our access point comparison. More on buying from an authorised Ubiquiti reseller in Australia.